Home > Customized

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Replacing a wheel bearing on your 2024 Chevy Malibu may seem daunting, but with the right tools, a little time, and some mechanical know-how, it’s a DIY job any driveway mechanic can tackle. The wheel bearing allows the wheel hub to spin freely on the spindle – when it goes bad, you’ll hear grinding, humming, or rumbling coming from the wheel area as you drive. Catching it early and swapping in a new bearing will save you bigger hassles down the road. Arm yourself with this 11-step guide and you’ll have that new bearing pressed in and rolling smoothly in no time.

Gather Tools and Supplies Needed for Wheel Bearing Replacement

Before wrenching, make sure you’ve got the proper equipment and gear. At a minimum, you’ll need basic hand tools – socket set and ratchet, wrenches, pry bar, mallet – plus a floor jack and sturdy jack stands. Don’t forget safety gear like gloves, eye protection, and wheel chocks. Parts-wise, purchase a complete hub assembly with the new wheel bearing pre-installed for your specific Chevy model. Having the right specialty tools makes the job easier too – things like a ball joint separator, puller, and bearing installer/remover kit can save lots of headaches.

Jack Up the Car and Support It Securely on Jack Stands

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Safety first! Find solid jacking points under the chassis, then lift the car high enough to give you room to work. Secure it on jack stands at both ends – never just rely on the jack. Chock the wheels still on the ground too. You want a stable base to prevent any shifting or dropping that could cause injury or damage.

Remove the Tire from the Wheel Hub Assembly

With access to the wheel well, use a lug wrench to loosen and remove the lug nuts so you can take the tire off the hub. Set it out of the way along with the lug nuts so they don’t get kicked or roll away.

Remove the Brake Caliper and Secure It Out of the Way

There are two bolts on the back of the caliper bracket that need to come out to detach it from the spindle. Hang it up securely using wire out of the way. Don’t let it dangle by the brake hose! Also remove the brake pads so they’re protected.

Remove the Brake Rotor and Set It Aside

With the caliper off, the rotor can slide off the hub. This exposes the wheel bearing assembly. Set the rotor somewhere safe – don’t just let it lay in the dirt!

Remove the Hub Dust Cap and Cotter Pin from the Spindle

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Pry off the hub cap in the center of the wheel hub to expose the spindle nut. Use pliers to remove the cotter pin that locks it in place. This pin keeps the nut from coming loose as you drive.

Remove the Hub Nut and Washer from the Spindle

With the cotter pin out, the hub nut keeping the wheel bearing attached to the spindle can now be removed. Take off the nut washer too. You’ll likely need a large socket and breaker bar for leverage here.

Separate the Hub Assembly from the Spindle

Things may still be stuck together! Use a mallet and drift pin to carefully break the hub free. Take care not to damage the ABS tone ring. The old bearing should now just slide right off the spindle.

Press Out the Old Wheel Bearing and Clean the Hub

With the hub off, the bearing can be pressed or driven out of the backside. Inspect closely for any cracks or damage. Use brake cleaner and rags to thoroughly clean the hub bore and mounting surfaces in preparation for the new bearing.

Pack and Install New Wheel Bearing into the Hub

Prep the fresh bearing by packing it with high-temp wheel bearing grease before installation. Then use a press or bearing driver to gently tap it into place within the hub. Proper seating is crucial, so take your time here.

Reassemble in Reverse Order and Lower Vehicle

Once the new bearing is seated correctly, rebuild by reversing the disassembly steps. Torque the spindle nut properly per spec, then insert a new cotter pin. Refit the brake components, rotor, tire, and lug nuts to complete the job. Carefully lower the car, remove the stands, and take a test drive.

With the right prep and procedure, a DIY wheel bearing replacement on a 2024 Chevy Malibu doesn’t have to be intimidating. Just work slowly and methodically, using quality parts and tools. Pat yourself on the back for saving the labor costs with your own elbow grease instead!

When that familiar rumble starts emanating from your 2024 Malibu’s wheel well, you know it’s time to swap in a new wheel bearing. This critical component allows the wheel hub to spin freely on the spindle, and worn out bearings mean grinding, noise, and eventual catastrophic failure if not addressed. Tackling a DIY replacement seems daunting, but have no fear – with the proper tools, focus, and a dash of elbow grease, you can have that new bearing pressed in and rolling silky smooth in no time flat.

Jack Up the Car and Support It Securely on Jack Stands

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Safety first and foremost before wrenching on your ride! Locate solid jacking points under the chassis, then use your floor jack to lift the car high enough to give you room to maneuver under there. Secure the car on sturdy jack stands at both ends to prevent any shifting, sliding, or (heaven forbid) dropping while you work. Chock those front wheels still on the ground for extra stability too. Take your time getting everything braced securely – you want a rock solid base before doing anything else.

Now you can really dive in to swapping that bearing! But hold up…you’ve gotta have the right gear first. Let’s talk tools and supplies.

Tool Up with the Essentials

Having the proper equipment makes the bearing swap a heckuva lot easier. Here’s a checklist of must-have items:

  • Floor jack and jack stands
  • Socket set with ratchet and extensions
  • Assorted wrenches
  • Pry bar
  • Mallet
  • Wheel chocks
  • Brake caliper hanger
  • Bearing puller/installer kit
  • Wheel bearing grease
  • Replacement bearing hub assembly
  • Safety gloves and eye protection

Round up all that gear ahead of time. The specialty tools like bearing pullers really come in handy too. And don’t forget to get the correct replacement hub assembly with new bearing for your 2024 Malibu!

Prep the Wheel Hub

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Now that you’re tooled up, it’s time to get hands on. Start by removing the tire so you can access the wheel hub assembly. Use a lug wrench to loosen and remove the lug nuts, then set the tire aside. Next, detach the brake caliper by removing the two bolts on the back. Hang it securely out of the way using a wire so it doesn’t dangle and strain the brake hose. Oh, and don’t forget to take out those brake pads too so they stay protected.

With the caliper off, the brake rotor can now slide off, exposing the wheel bearing assembly. Set it somewhere safe so it doesn’t get scratched or dirty. Almost there…

Separate the Hub from the Spindle

A few more steps and you’ll be ready to pull that bad boy off. Pop off the hub dust cap in the center to uncover the spindle nut. Use pliers to remove the cotter pin that locks it in place. Then unthread the nut along with the washer. Things might still be stuck on there tightly, so brace the hub assembly and use a mallet and drift pin to give it a few good whacks to break it free from the spindle. Patience and care here prevents damage. Now you can finally slide that sucker off!

Press In a Pretty New Bearing

With everything apart, use your bearing puller to remove the old bearing from the hub. Inspect closely for any cracks or flaws. Clean all mating surfaces thoroughly before pressing in the fresh bearing – contamination is the enemy! Pack the new bearing with high-temp wheel bearing grease first. Using a press or bearing driver, gently tap the bearing into place within the hub. Proper seating is critical, so take it slow.

Once fully seated, you’re ready to put the puzzle back together. Just reverse all the steps, torquing the spindle nut to spec and inserting a new cotter pin. Refit the brake components, rotor, tire, and lugs. Carefully lower the car, remove the stands, and take your baby for a test spin. Listen and feel for any noise or vibration. Silky smooth? You just conquered a bearing swap – way to go!

That familiar humming coming from your 2024 Malibu’s wheel well can only mean one thing – it’s time to replace the wheel bearing. This critical component allows the wheel hub to spin freely on the spindle, and worn out bearings mean noise, vibration, and eventual failure. While it may seem intimidating, you can totally handle a DIY replacement with the right prep and procedure. Just take it slow and steady, and that new bearing will be rolling smooth in no time.

Remove the Tire from the Wheel Hub Assembly

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Now that you’ve got the car safely lifted and secured on jack stands, you’re clear to start disassembling to access the wheel bearing. First up is removing the tire so you can get to that hub assembly.

Use a lug wrench to loosen each lug nut, then carefully pull the tire off the wheel hub. Set it aside along with the lug nuts so they don’t wander off and get lost. Pro tip: resting it face down prevents scratches on the rim.

Disengage the Brake Caliper

With the wheel removed, you’ll see the brake caliper mounted to the backside of the spindle. To detach this, remove the two bolts that hold the caliper bracket in place. Once unfastened, hang the caliper assembly out of the way using a sturdy wire or hook. Don’t let it just dangle by the brake hose!

Oh, don’t forget to take out the brake pads from the caliper too. Set these aside somewhere clean so they don’t get contaminated with dirt or debris.

Slide Off the Brake Rotor

With the caliper detached, the brake rotor can now slide right off the wheel hub. This exposes the wheel bearing assembly. Set the rotor gently on a clean surface to keep it from getting scratched up while you work.

Pop Off the Hub Dust Cap

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

See that round dust cap in the center of the wheel hub? Use a flathead screwdriver to pry this off, exposing the spindle nut behind it. This nut holds the wheel bearing onto the spindle.

Remove Cotter Pin and Spindle Nut

Use needle-nose pliers to grab and remove the thin cotter pin from the spindle hole. This little guy keeps the spindle nut from rattling loose. With the cotter pin out, you can now unthread the spindle nut along with the washer behind it using a socket wrench. You’ll likely need an extension and cheater bar for leverage here.

Free the Hub from the Spindle

Even with the nuts removed, the hub may still be stuck tight on the spindle. Use a few gentle whacks with a mallet on the backside to pop it loose. Take care not to damage the ABS tone ring during this step. Once freed up, you can now slide the hub and old bearing off the spindle.

With access to that pesky bearing, it’s time for the fun part – pressing in the new guy!

That familiar grinding or rumbling coming from your 2024 Malibu’s wheel well can only mean one thing – it’s time to replace the wheel bearing. This DIY repair may seem intimidating, but having the right tools and focusing on each step of the process will have you rolling smoothly again in no time. Let’s continue taking things apart to get access to that worn bearing.

Remove the Brake Caliper and Secure It Out of the Way

With the tire removed, you now have access to the brake components. The caliper needs to come off next to expose the wheel hub and bearing assembly. Here’s how to remove it safely:

Locate the Caliper Mounting Bolts

On the backside of the spindle, you’ll see two bolts that hold the brake caliper bracket in place. Use a socket wrench with an extension to access and loosen these bolts.

Detach the Caliper from the Spindle

As you loosen the bolts, the caliper will detach from the spindle. Be prepared to support it as the bolts come all the way out. Also have a sturdy wire or hook ready to hang it safely out of the way.

Don’t Let It Dangle!

With the caliper off the spindle, don’t just let it hang from the brake hose! This puts dangerous strain on the hose. Secure it properly on a hook or wire near the working area.

Remove the Brake Pads

The brake pads will slide right out of the caliper bracket once detached. Remove them and set them someplace clean so they don’t get contaminated.

Inspect the Caliper and Hose

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Check the caliper and brake hose for any cracks, leaks or damage while you have them accessible. Catching issues now means avoiding bigger problems down the road.

Clean and Lube the Caliper Sliders

Use some brake cleaner spray and a rag to wipe down the caliper slider pins. Put a thin coating of silicone lube on them to prevent sticking and ensure smooth operation.

With the caliper safely out of the way, you’re clear to move on to removing that rotor and accessing the wheel bearing next. Just be diligent about keeping those brake components clean during the rest of the job.

That familiar rumbling from your 2024 Malibu’s wheel area likely means a worn out wheel bearing. Replacing it yourself may seem daunting, but taking methodical steps during disassembly will get you there. With the brake caliper already detached, you’re ready to move on to removing the rotor and exposing that pesky bearing.

Remove the Brake Rotor and Set It Aside

Now that the brake caliper is out of the way, the brake rotor can be removed to access the wheel bearing assembly. Here’s how to remove it safely:

Wiggle the Rotor Off the Hub

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

The rotor should slide right off the wheel hub once the caliper is detached. Wiggle it gently side-to-side while pulling outward. It may take a little effort if corroded on there.

Watch Your Fingers!

Rotors have sharp edges, so wear thick gloves during removal. Also watch out for the abrasive surface that contacts the brake pads.

Set It Someplace Clean

Don’t just toss the rotor on the ground! Set it gently onto a clean surface to avoid scratching the smooth side. Contaminating it with dirt, grease, or debris will affect braking performance.

Inspect and Clean if Needed

While removed, take a close look at the rotor surface for damage or excessive wear. Use brake cleaner and rags to remove any built-up gunk if needed.

Avoid Contact with Grease/Oil

Be very careful that grease or oil does not get onto the rotor friction surface. This will degrade braking performance once reassembled.

With the rotor out of the way, you now have open access to the wheel bearing. Getting to this point carefully and methodically is half the battle – now it’s time for the fun stuff!

That familiar grinding coming from a 2024 Malibu wheel well indicates a worn out wheel bearing. Replacing it yourself can save time and money with the right approach. Removing components like the rotor gets you close, but a few more steps expose that pesky bearing.

Remove the Hub Dust Cap and Cotter Pin from the Spindle

With the brake rotor detached, focus turns to the wheel hub itself. Here’s how to remove the items securing it to the spindle:

Pry Off the Central Dust Cap

There’s a round plastic dust cap in the center of the wheel hub. Use a flathead screwdriver to pop this off, exposing the end of the spindle.

Locate the Cotter Pin Hole

Look for a small hole drilled in the end of the spindle near the edge. This is where the cotter pin is inserted.

Use Pliers to Remove Cotter Pin

Grab the cotter pin firmly with a pair of needle-nose pliers and pull it straight out of the hole. Take care not to bend or break it.

Examine the Cotter Pin

Inspect the removed cotter pin for any damage or excessive wear. A stretched or fatigued pin means replacement is required during reassembly.

Set it Aside Somewhere Safe

Don’t just toss the cotter pin on the ground! Set it somewhere clean for potential reuse or comparison later.

Extracting the cotter pin allows removal of the hub nut next. Getting to this point methodically is crucial – great work! Only a few more steps until that bearing comes out.

That familiar grinding or rumbling from the wheel area of your 2024 Malibu is a telltale sign of a worn out wheel bearing that needs replacing. Removing the rotor and cotter pin gets you closer to that pesky bearing – now to detach it from the spindle.

Remove the Hub Nut and Washer from the Spindle

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

With the cotter pin extracted, you can now remove the hub nut and washer holding the bearing assembly onto the spindle. Here’s how to do it safely:

Locate and Fit the Proper Socket

The hub nut has a large hex shape designed for a socket. Locate the correct size socket and extension for accessibility.

Brace Against the Hub

Hold or brace the hub assembly firmly with one hand while loosening the nut with the other. This prevents spinning.

Break the Nut Free

Put force on the ratchet/breaker bar to initially break the nut free. Penetrating lube may help if resistant.

Back it Off Completely

Once broken loose, unthread and remove the nut completely along with the washer behind it.

Inspect for Damage

Examine the nut and washer for damage like cracks or stripped threads. Damaged items should be replaced.

Set Aside Carefully

Don’t just toss the nut and washer on the ground! Place them somewhere clean and protected.

With the hub nut detached, you’re so close to freeing that pesky bearing. Just a few more precise steps stand between you and wheel bearing replacement success!

That familiar rumbling or grinding sound coming from your 2024 Malibu’s wheel area indicates a bad wheel bearing needing replacement. Removing components like the caliper, rotor and hub nut gets you close to freeing that pesky bearing from the spindle.

Separate the Hub Assembly from the Spindle

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Even with the securing nuts removed, the hub and bearing may still be stuck on the spindle. Here’s how to separate them safely:

Brace the Hub Assembly

Hold or brace the hub firmly with one hand to prevent it spinning when applying force.

Use a Mallet and Drift Pin

With the hub braced, use a mallet and drift pin to apply targeted force where the hub meets the spindle.

Give It a Few Sharp Raps

A few sharp raps is often all it takes to break the hub free. Don’t overdo it! Too much force can damage components.

Work Around the Perimeter

Hit different points around the spindle/hub junction to evenly break the seal all the way around.

Pull the Hub Off By Hand

Once loosened, remove the hub assembly by hand, sliding it off the spindle shaft.

Avoid ABS Ring Damage

Work carefully during removal to avoid damaging the ABS tone ring behind the hub.

Getting that stubborn hub separated safely is crucial. Now the fun part – freeing the worn bearing and installing the fresh new guy!

That familiar grinding or rumbling from your 2024 Malibu’s wheel area is a classic sign of a bad wheel bearing that needs replacing. Getting the hub separated safely from the spindle provides access to remove that pesky worn bearing.

Press Out the Old Wheel Bearing and Clean the Hub

With the hub assembly detached, you can now remove and replace the worn wheel bearing. Here are some tips for safe removal and prep:

Inspect the Old Bearing

Take a close look at the bearing you removed. Check for excessive wear, pitting, cracking, or missing ball bearings as clues to failure.

Use a Press or Bearing Puller

A press or slide-hammer style puller makes safe bearing removal easier. Use gradually increasing pressure.

Support the Hub Properly

Secure the hub assembly properly before pressing/pulling to avoid component damage during removal.

Clean All Mating Surfaces

Use brake cleaner and rags to thoroughly clean the hub bore and mounting surfaces of old grease and debris.

Avoid Contamination

Proper cleaning prevents bearing contamination upon reassembly. Even a small spec can cause premature failure.

Dry and Inspect the Hub

Allow surfaces to fully dry and inspect for any pitting or damage before reassembly. Address any issues found.

Careful old bearing removal and meticulous hub prep are vital steps before pressing in that fresh new wheel bearing.

That familiar noise coming from the wheel area of your 2024 Malibu is a clear sign the wheel bearing needs replacing. Removing the old bearing and cleaning the hub properly preps for installation of the new guy.

Pack and Install New Wheel Bearing into the Hub

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

Once the old bearing is out and the hub prepped, it’s time to install the new wheel bearing. Here are some tips for proper installation:

Inspect the New Bearing

Look over the replacement bearing before installing – make sure it’s in good shape with no defects or missing balls.

Pack It with Grease

Pack the bearing cavities fully with fresh high-temperature wheel bearing grease before pressing it into the hub.

Support the Hub Properly

Secure the hub in a press or vise properly to avoid damage as you install the new bearing.

Press in Gradually

Use smooth, gradual pressure on a bearing installer tool to press the bearing into the hub bore until fully seated.

Seat Completely

Make sure the bearing is pressed completely flush within the hub for proper fit and sealing.

Don’t Get Overzealous

Applying too much pressure can damage the bearing. Take it slow and check frequently during installation.

Installing that new wheel bearing properly is vital – take your time here. Next step – get everything bolted back up and enjoy a smooth rolling ride!

That familiar grinding or rumbling coming from the wheel area is a surefire sign your 2024 Malibu’s wheel bearing needs replacing. You’re in the home stretch after carefully installing that new bearing into the cleaned hub.

Reassemble in Reverse Order and Lower Vehicle

How to Replace a Wheel Bearing in Your 2024 Chevy Malibu: An 11-Step Guide

With the fresh wheel bearing correctly pressed into the hub, it’s time to button things back up:

Replace Hub Nut and Washer

Slide the hub assembly onto the spindle and replace the washer and nut to secure it. Tighten the nut to spec.

Insert New Cotter Pin

Insert a new cotter pin into the hole on the spindle to lock the nut in place and prevent loosening.

Refit Brake Components

Carefully remount the brake rotor, caliper and pads in reverse order of disassembly.

Don’t Contaminate Rotors

Ensure no grease or debris contacts the brake rotor friction surfaces during reassembly.

Replace Tire and Lug Nuts

Reinstall the wheel onto the hub and hand tighten the lug nuts in a star pattern.

Lower Vehicle and Torque Lugs

Raise the car, remove jack stands, then lower fully and torque lug nuts to spec with a wrench.

Test Drive Time

Take it for a quick spin to ensure smooth, vibration-free operation before considering the bearing swap complete.

Carefully following the entire replacement process pays off big when you hit the road and enjoy a rattle-free ride again!