Home > Customized

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Heating Element Not Working? Check Kenmore 796.81182310 Parts

Is your Kenmore dryer not heating up anymore? Don’t despair – with a few handy troubleshooting tips, you can likely get your dryer heating again in no time. As a long-time Kenmore owner myself, I’ve been through a few dryer repair journeys, so I wanted to share what I’ve learned.

First, make sure your dryer is getting power. Check the breaker or fuse box and ensure the circuit for the dryer is not tripped. Also check that the power cord is securely plugged into the outlet. If there is power getting to the dryer but it’s still not heating up, the problem likely lies with the heating element.

The heating element on Kenmore dryers like the 796.81182310 is what heats the air inside the drum to dry the clothes. It’s basically a big coil of wire that gets red hot. Over time, these coils can burn out and stop working properly. If the dryer is running but not heating, the heating element should be the first thing to check.

Start by unplugging the dryer and removing the back panel. The heating element is located inside the dryer drum usually behind the blower housing. Visually inspect the coil for any breaks or worn spots. Use an ohm meter to check the continuity of the coil – you should get a complete circuit. If the readings indicate an open break in the circuit, it means the heating element needs to be replaced.

Replacement Kenmore heating elements can easily be found online through parts suppliers. Be sure to search for the specific part number for your model, like the 279838 for Kenmore 796.81182310 dryers. These are usually inexpensive, ranging $20-60 for most models. The repair is fairly straightforward with some disassembly required to access the element coils.

First disconnect the power supply wires, then remove any brackets or screws holding the coil in place. Slide out the bad element and replace with the new one, being careful not to damage the fragile coil windings. Reinstall any removed parts and reconnect the wires as they were. With the fresh heating element installed, your Kenmore should now heat up as good as new!

One tip if you are handy – you can actually test a heating element right on your kitchen stove! Just be extremely careful not to burn or shock yourself. Hold the coil over a burner for 30 seconds. If it glows red, it likely still has continuity. This can save you the cost of a new part if the old element checks out ok.

Other things to check would be the high-limit thermostat, thermal fuse, and cycling thermostat. But in most cases, a lack of heat points to a failed heating element. With a few basic tools and safety precautions, you can troubleshoot and replace this key part on Kenmore dryer models like the 796.81182310 and get your clothes dry once again!

Noisy Operation? Replace Belt on Kenmore Dryer Model 796

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Is your Kenmore dryer starting to sound like a rock tumbler when running? Loud, squealing, squeaking or thumping noises coming from the dryer can be annoying and disruptive. Often, the culprit is a worn out drive belt that needs replacement.

The drive belt on Kenmore dryers like the model 796 connects the motor to the drum and spins it during operation. Over time, these belts can become cracked, frayed or off track. This causes rubbing, friction and uneven spinning that translates into irritating noises.

Replacing a dryer belt is an easy DIY fix. First unplug the dryer and use a putty knife or screwdriver to help pry off the front panel. This will expose the belt and pulley system. Slip the old belt off the pulleys and examine it for damage. Look for cracking, shredding or uneven/frayed edges as signs it needs to be replaced.

Search online for the specific replacement belt for your Kenmore model number. They usually run $10-20. Carefully loop the new belt over the pulleys according to the routing diagram or markings. Ensure it is not twisted and spins smoothly by rotating the drum by hand. Reinstall the front panel and plug in the dryer.

With a fresh drive belt installed, noisy operation should be greatly reduced or eliminated. Be sure to run the dryer empty for several cycles to allow the new belt to properly seat itself on the pulleys. Keep an ear out for any lingering noises which could indicate another underlying problem.

Regular dryer maintenance goes a long way towards preventing annoying noises. Be sure to clean the lint trap before each load to prevent accumulation on internal parts. Vacuum excess buildup around vents and ductwork. And try rubbing a dryer sheet on the drum – it can help reduce static friction noise. But when noises persist, replacing a worn drive belt is often the solution to quieter operation.

Burning Smell? Check Lint Trap on Kenmore 81182310

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Uh oh, is your Kenmore dryer emitting a burning odor? That’s never a good sign. In many cases, a burning smell from a dryer indicates an excess buildup of lint inside the machine. Lint traps on models like the Kenmore 81182310 should be checked and cleaned regularly to help prevent this problem.

The lint trap is usually located right inside the dryer door. It’s essentially a filter that catches all the lint, hair, and debris that detaches from fabrics as they tumble around inside the heated drum. Over time, this lint can accumulate and clog the narrow openings in the trap. Excess lint buildup impedes proper airflow through the dryer which can lead to overheating.

It’s recommended to clean out the lint trap before each and every dryer load. Simply pull out the trap and use your fingers or a brush to wipe away any visible lint. You can also use the hose attachment on a vacuum cleaner to suction out any trapped lint from the filter screen. Ensure you remove all traces of lint and that none remains stuck in the mesh openings.

A clogged lint trap forces hot air to back up inside the dryer instead of venting properly outside. This creates increased heat friction on internal parts like belts and rollers. The burning smell is often times excess lint burning inside the dryer. Cleaning the lint trap thoroughly before each load helps eliminate fire hazards and burning odors.

In addition to the lint trap, also periodically use a vacuum hose to extract lint buildup from the duct vent, blower housing, and exhaust hood outside. Avoid kinking flexible exhaust hoses which can impede airflow. And ensure outside wall vents have proper louver openings and are not obstructed by screens or debris.

By maintaining a clean lint path and trap, dryers like the Kenmore 81182310 can operate safely for years without any burning smells. But if odors persist after a thorough cleaning, have an appliance technician inspect the machine for any mechanical failures or damaged parts which could require repair.

Don’t ignore burning odors – clear lint buildup promptly. With consistent trap maintenance, your clothes and home stay safe while preventing frustrating dryer issues.

Long Drying Times? Clean Vent on Kenmore 796.81182310

Is it taking forever for your Kenmore dryer to actually dry clothes? Extra long drying cycles are often the result of restricted airflow through clogged vents. For models like the Kenmore 796.81182310, a thorough vent cleaning can help speed up drying time.

As moisture is evaporated out of wet laundry inside the tumbling dryer, it needs to vent outdoors through the exhaust system. Lint and other debris can gradually clog up vent pipes, hoses, and exterior wall vents over time. This restricts the rate of airflow and moisture ventilation.

Start by disconnecting the dryer from the wall vent. Use a vacuum hose to extract any visible lint buildup from inside the vent opening. Carefully reconnect the vent pipe. Detach the flexible vent hose from the back of the dryer. Use a vent brush and vacuum to remove any accumulated lint inside the hose.

Finally, go outside and inspect the exterior vent hood. Use a small wire brush to clear any debris clogging the louvers. Verify the damper flap moves freely to open during dryer use. Aim a flashlight inside the vent opening to check for any obstacles like bird nests or insect webs.

Reconnect the system once fully cleaned. Test run the dryer empty and confirm strong airflow by holding tissue or streamers up to the outside louver opening. Proper venting should suck air quickly through the outlet. If airflow still seems weak, the entire duct run may need professional cleaning or replacement.

Prevent future buildup by laundering lint-producing fabrics inside out. Use mesh laundry bags for small loose items like socks. And always promptly clean the lint trap before each load. Keep the full venting path unobstructed for optimal drying power on Kenmores like the 796.81182310.

With a clean exhaust pathway, moisture can properly vent outdoors instead of getting trapped inside. Say goodbye to endless drying cycles and hello to faster dry times.

I hope these dryer troubleshooting tips help extend the life of your Kenmore appliance. Let me know if you have any other repair questions! Dryers may break down eventually, but don’t let small issues steam-press your patience. With a bit of DIY maintenance, you can keep your Kenmore smoothly tumbling along for years to come.

Is your Kenmore dryer making an obnoxious rumbling or squeaking noise when running? Don’t panic – noisy operation is one of the most common problems with clothes dryers, and is often an easy fix. With some basic troubleshooting, you can likely resolve the issue yourself without calling in expensive appliance repair technicians.

First, let’s go over some of the typical causes of a noisy dryer so you know what to look for. The most common culprits are:

Worn drum bearings

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Over time, the drum bearings that allow the dryer tumbler to spin smoothly wear out. This causes the drum to rub or grind against other parts of the dryer, creating a scraping or squealing noise. Replacing the cheap bearings is usually pretty straightforward.

Loose drum glides

The plastic or nylon glides that support the dryer drum can become brittle and crack with age. If they become loose or break off completely, it allows the drum to rub on the metal centerpost and make noise. Like bearings, the glides are inexpensive and fairly easy to replace.

Damaged drum supports

The cylindrical rollers at the back of the drum that prevent front-to-back movement can also wear out or break over time. A damaged or missing roller will cause the dryer drum to scrape loudly against the cabinet during operation. The rollers are easy to inspect and replace.

Loose blower housing

The housing surrounding the dryer’s blower fan can become loose and vibrate against the cabinet. This creates a loud rumbling or rattling noise, usually worse at high speeds. Tightening the blower housing screws and braces typically solves this problem.

Belt tensioner misaligned

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

The spring-loaded belt tensioner keeps the drive belt tight as it turns the drum. If the tensioner shifts out of position over time, it can cause the belt to rub loudly against neighboring pulleys or the motor housing. Realigning or replacing the tensioner is a quick fix.

Worn drive belt

A loose, cracked, or slipping drive belt is another prime suspect for rumbling and squeaking. The belt connects the motor to the drum and can gradually wear out and lose traction. Replacing the belt is a 5 minute job in most dryers.

Now that you know what to look for, inspecting your noisy Kenmore dryer model 796 to find the problem is straightforward. First, unplug the dryer and pull it out from the wall so you can access the back panel. Take off the panel to expose the inner workings.

Check the condition of the drum glides and front support rollers. Do they look cracked, loose, or misshapen? Try spinning the drum by hand – does it make scraping noises against the metal centerpost? If so, the glides or rollers likely need replacing.

Inspect the drive belt next. Check for cracking, glazing, fraying, and excessive looseness. Try turning the motor pulley and drum pulley by hand – if the belt slips, it needs to be changed. Also verify the belt tensioner spring is centered and holding the belt taut.

Examine the blower housing where it meets the dryer cabinet. Is it firmly tightened against vibration, or can you wiggle it? Try tightening the mounting screws with a wrench to see if that stops any rattling noises.

Finally, remove the front panel so you can access the drum bearing at the very back. Have an assistant turn the drum slowly while you feel for grinding or rubbing in the bearing behind it. Any roughness indicates worn bearings in need of replacement.

Order any needed replacement parts for your Kenmore model online or from an appliance parts supplier using the model 796 and serial number printed on the data plate. Most parts are widely available for DIY repairs. The belt, glides, rollers, and tensioner can be swapped out easily in around 30 minutes or less. Replacing bearings takes a bit more work but can still be DIY’ed with some mechanical aptitude.

Following proper troubleshooting steps methodically and inspecting each component is key to zeroing in on what’s causing the noise in your Kenmore dryer. With the right replacement parts on hand, there’s a good chance you can knock out a repair yourself and get your dryer running quietly again. But if the problem proves too complex, don’t hesitate to call in an appliance service technician.

Uh oh, is your Kenmore dryer letting off a burning odor when running? That can’t be good. But before you panic and call the fire department, investigate whether a clogged lint trap could be the culprit. With a few easy cleaning steps, you can often eliminate burning smells coming from Kenmore models like the 81182310.

First, what causes a burning smell in a clothes dryer? There are a few common culprits:

Clogged lint trap

The most obvious source of burning odors is lint buildup inside the trap housing. Lint is highly flammable, and if enough accumulates it can overheat from the heating element and smolder or catch fire. Cleaning the trap regularly prevents this.

Restricted venting

If the vent hose or outdoor vent hood become blocked, it restricts airflow out of the dryer. This causes overheating, potentially leading to burning smells. Inspect the full vent run and clean any blockages.

Bad thermostats

Faulty high limit safety thermostats can fail to shut off the heating element when the dryer overheats. This can burn lint or other debris, emitting a burning odor. The thermostats need replacement if defective.

Damaged heating element

Excessive aging or overheating can damage the heating element itself. This can cause electrical shorting or burning at the element, creating a burning smell. Inspect the element and replace if worn out.

So for your Kenmore 81182310 or other model, start troubleshooting a burning odor by thoroughly cleaning the lint trap. Here are some tips:

Clean the trap housing

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Pull out the lint trap and use a vacuum crevice tool to clean around the opening and trap housing. Lint can accumulate here even if you clean the filter regularly. Go back as far as you can reach.

Check the duct chute

Detach the duct from the vent housing so you can inspect the chute where lint exits the drum. Use a vacuum or pipe cleaner to remove any compacted lint inside the chute.

Clean the blower fan

The blower fan behind the housing can get caked with lint too. Remove the housing and vacuum the fan blades and surrounding compartment.

Wash the filter

For stubborn lint stuck to the lint trap screen, remove it and wash with warm water and soap. This loosens stuck-on residue and fully cleans the screen mesh.

Check the duct run

Inspect the entire dryer vent duct from the chute to the outdoors vent hood. Clean out any lint accumulation or blockages with a vacuum. Lint can stick anywhere inside the run.

After thoroughly cleaning the lint system, reassemble and test your Kenmore dryer. Run it empty on high heat for 20 minutes, keeping your nose near the vent hood outside. If you still smell any burning, there’s likely another issue besides lint buildup.

Double check the venting ductwork again for any blockages you may have missed. Then inspect the heating element itself inside the dryer. Look for visible scorching or pitting from overheating. Use an ohmmeter to check the element for continuity. If defective, it will need replacement.

Also check the dual high limit thermostats mounted to the heating element housing. You can test them for continuity at room temperature. If faulty, replace both thermostats as a pair. Burnt lint around the thermostats is a sign they need replacement.

If the burning smell only happens during the heating cycle, the problem is likely with the heating system. But if it occurs all the time the dryer is running, the drive motor could be overheating too. This could indicate defective motor windings or bad bearings causing friction.

It’s worth taking the belt off and manually turning the drum and motor by hand to feel for grinding or catching. If the motor seems noisy, binding or loose, replacement may be needed. Match the part number printed on the motor when ordering a new one.

With some methodical troubleshooting and component testing, you can zero in on what’s causing burning odors in your faulty Kenmore dryer. Repairing the problem yourself can save the cost of a service call. Just be sure to address any overheating issues promptly before they create a fire hazard.

While a clogged lint trap is often the culprit, severe overheating can damage other dryer parts over time. It’s a smart idea to go ahead and replace the thermostats and inspect the element and motor when you experience any burning smells from your Kenmore. A few inexpensive new parts can help ensure safe and reliable operation down the road.

Is your Kenmore 796.81182310 or similar model taking forever to dry loads? Do you have to run multiple cycles to get clothes fully dry? The problem could be a restricted air vent clogging airflow and hampering efficiency.

When dryers can’t properly expel warm, moist exhaust air outdoors, it causes longer drying times. Here are some common venting problems that may affect your Kenmore:

Crushed or kinked duct

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Dryer ducts can easily get crushed behind the machine or kinked when moving the dryer. Any deformities in the duct restrict airflow and reduce drying performance. Straighten or replace crimped sections.

Clogged vent hood

Outdoor dryer vent hoods can become clogged with lint, leaves, nests and other debris. Regularly inspect and clean the outdoor vent opening to ensure maximum airflow.

Excess duct length

Long vent runs over 25-30 feet with multiple elbows cause back pressure. This slows airflow through the system. Use rigid metal duct and reduce duct length for optimal drying.

Lint accumulation

Lint can coat the inner duct over time and significantly reduce airflow and exhaust velocity. Detach and clean the duct periodically to maintain full drying efficiency.

To maximize airflow and drying power, it’s important to clean and inspect the full venting system on your Kenmore dryer.

Detach and clean duct sections

Take apart the duct sections and use a vacuum cleaner to remove lint accumulation inside. Go from the dryer outlet to the outside vent hood.

Clear vent hood screen

Use a wire brush to dislodge any debris clogging the hood screen outside. Hose it off and let it fully air dry before reinstalling.

Straighten any kinks

Check that ducting is fully extended and smooth. Reposition any sections that are crushed or kinked. Use metal duct where possible.

Confirm duct length

Measure your full vent run from the dryer to outdoor hood. Keep it under 25 feet with minimal elbows. Reduce length if currently longer.

Check for lint escapes

Inspect along the duct joints and duct-wall connections for gaps where lint could escape into the wall cavity. Seal any leaks with metal tape.

Also check the outdoor vent hood flapper to make sure it opens fully when the dryer is running. Bend or replace the flapper if it appears stuck closed.

After cleaning the system, run a test load on high heat and check airflow at the outdoor vent. Hold a tissue up to the hood when the dryer is running. It should stick firmly in place over the hood due to strong exhaust airflow.

If the tissue doesn’t stick, it usually indicates remaining vent blockages or leaks. Retest duct connections and joints for any gaps or clogs. Confirm the vent hood flapper opens fully during operation.

You can also purchase a dryer vent testing kit. This includes a measuring manometer that attaches to the duct to measure airflow pressure. A reading of less than .1 inches of water column pressure indicates restricted airflow requiring further cleaning.

If your Kenmore dryer runs for 40-60 minutes or longer to fully dry a normal load, restricted venting is likely the problem. Thoroughly cleaning the full vent system typically restores normal drying times.

For safer drying, remember to clean lint from the duct, vent hood and trap housing every 6 months or so. Also immediately investigate any new drying performance issues, which could indicate a new lint accumulation or obstruction.

Quickly address any venting problems you discover to maximize your Kenmore’s efficiency and drying power. Doing so reduces utility costs, speeds up drying cycles, and improves dryer lifespan by eliminating overworking.

And take the time to confirm your dryer vent setup follows recommendations: use rigid metal duct, make sure the run is under 25 feet, and allow for easy access to clear obstructions. Proper dryer venting is essential for fast, efficient, safe drying.

Are your clothes coming out overly wrinkled and creased when drying loads in your Kenmore 81182310? The dryer timer may need an adjustment to allow clothes to tumble sufficiently after heating shuts off.

Wrinkling issues can occur when the timer advancing mechanism fails to keep clothes tumbling for a long enough cool-down period. Here’s what happens inside the dryer:

Heating time

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

During the initial heating cycle, clothes begin to dry from the heat and tumbling action. The timer holds the heating on as the cycle progresses.

Cool-down time

After the clothes reach the desired dryness level, the timer shuts off the heat but keeps the drum tumbling. This cool-down time allows clothes to relax and smooth out wrinkles before the end of the cycle.

Insufficient cool-down

If the timer advances too quickly, the cool-down period is cut short. Clothes don’t get enough tumbling time to unwind wrinkles after drying. This leaves them crumpled as the cycle ends.

To optimize the cool-down time on your Kenmore dryer:

Check timer operation

Use the timer dial to manually advance through a full cycle. The drum should keep turning for several minutes after the heat shuts off. If it doesn’t, the timer needs adjustment.

Extend cool-down time

Open the timer housing and locate the cool-down cam. Bend it slightly to increase the low-heat tumbling time at the cycle end. Test and tweak as needed.

Listen for timer ticks

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Does the timer make rapid ticking noises right before the cycle ends? This indicates it’s advancing too quickly through cool-down. Contact a technician for repair.

Use air-dry setting

If available on your model, use the air fluff or air-dry cycle setting. This provides extended tumbling with no heat to unwind wrinkles.

Also check that the timer dial is actually advancing fully through the end of the cycle. Common timer issues that can lead to insufficient cool-down include:

Sticking contacts

Buildup on the electrical contacts can prevent the timer from advancing to the final cooldown stage. Use a contact cleaner spray to clean the contacts.

Worn parts

The internal motor, gears, and cams that drive timer operation can wear out over time. This may cause the timer to stall mid-cycle. Replace damaged components.

Loose knob

If the knob wobbles excessively, the internal timer shaft may be stripped. Tighten or replace the knob and shaft as needed to ensure proper advancement.

Drive belt slippage

Belt wear or motor slippage prevents the drum from continuing to turn during cool-down. Inspect the drive belt and pulleys for wear and tighten as needed.

Be sure to clean lint and debris frequently from around the timer dial shaft, contacts, and housing. This helps prevent binding issues over time.

Also confirm that loads aren’t oversized. Stuffing too many clothes into the dryer can leave insufficient air space for tumbling during cool-down. Use smaller loads if needed.

For optimal wrinkle prevention, use fabric softener sheets and promptly remove clothes once the cycle finishes. The less time clothes sit bunched up in the dryer, the smoother they’ll be.

If adjusting the timer or replacing worn parts doesn’t resolve recurring wrinkling issues, other factors like baffle damage or belt tension may need attention. But in most cases, focusing on maximizing cool-down tumbling time is the key.

While you have the timer open for inspection, it’s a smart idea to clean and lubricate components to ensure reliable functioning. A little preventive maintenance goes a long way to preventing future drying issues and prolonging the life of your Kenmore appliance.

Is the door on your Kenmore dryer model 796 constantly popping open when running? An improperly latching door can be annoying and unsafe. But with a few quick inspection tips, you can get the dryer door staying tightly shut.

Start by understanding how the door latch mechanism works on Kenmore dryers:

Latch assembly

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

A large hook-shaped latch is mounted inside the door, which clicks into place over a catch on the dryer front when closed.

Lock bar

A metal bar activated by the handle presses against the latch to hold it tightly against the catch while closed.

Spring tension

A spring provides resistance to engage the latch firmly into the locked position over the catch when the door closes.

Release button

Pressing the release button disengages the lock bar so the latch can open and release from the catch.

If the door isn’t staying latched during operation, here are some key things to check:

Inspect latch condition

Examine the latch inside the door for any visible wear, warping or damage. If defective, replace the entire latch assembly.

Check catch alignment

Make sure the catch on the dryer front is straight and aligned to properly fit the latch. Adjust if needed.

Test lock bar motion

When activating the handle, the lock bar should press firmly and evenly. If not, adjust or replace the bar.

Clean and lubricate

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Remove any built-up lint around the latch components. Lightly lubricate the pivot points with dryer-safe lubricant.

Examine door seal

A damaged door seal can allow air leaks that pop the door open. Inspect the seal and reattach or replace if needed.

You’ll need to unplug the dryer and remove the top panel to access the latch mechanism for inspection and testing. When reassembling, check the following:

Spring tension

The latch return spring should provide firm resistance when closing the door. Increase tension if the latch isn’t drawn closed tightly.

Lock bar friction

Some resistance should be felt when sliding the lock bar against the latch. If too loose, adjust the bar bracket.

Latch hook shape

The hook part that grasps the catch should be curved inward. Straighten if bent outward.

Catch engagement

Listen for the latch clicking solidly into place over the catch when closing the door. Adjust alignment if needed.

Also examine the door hinges to make sure the door assembly is hanging straight within the cabinet opening. Shim any hinges that are loosening or sagging.

Additionally, inspect the tumbler baffle located inside the dryer drum. If it becomes damaged, clothing can get caught and pull the door open during operation. Replace the baffle if bent or torn.

Confirm adequate clearance around the dryer. Restricted space can prevent the door from closing fully. Give the dryer a few inches of breathing room all the way around.

Test operate the dryer with an empty load to verify the door stays firmly latched throughout the cycle. You may need to fine tune the lock bar or latch adjustments.

In most cases, a thorough inspection and cleaning of the door latch components is all that’s needed to get a Kenmore dryer door staying tightly closed. Adjusting the latch spring tension is also useful to compensate for any parts that have loosened up over time.

But if the latch assembly is damaged or badly worn, replacement will be required. You can easily find replacement Kenmore dryer parts online or from appliance parts suppliers using your model number.

Is your Kenmore 796.81182310 dryer refusing to start? Before you take on a full electrical teardown, check whether a faulty start switch is the culprit. This common failure is an easy DIY fix that doesn’t require rewiring skills.

The start switch activates the motor circuit when you press the button to start a dryer cycle. If the switch contacts become damaged or worn, the dryer may not turn on at all. Here’s a quick troubleshooting guide for a no-start condition:

Check power supply

Use a multimeter to confirm 120V power is reaching the dryer’s terminal block. If not, check the home’s breaker or fuse box for a tripped circuit.

Inspect door switch

The door switch disables operation when open. Jump the door switch wires at the control board to rule it out as the no-start culprit.

Test start button

Press the start button and listen for a click. No click indicates a faulty push-to-start switch that requires replacement.

Bypass start switch

Disconnect the start switch wires and short them together directly. If the dryer starts, the switch is bad. Reconnect wires after verifying.

Check motor

If the motor itself is burned out, jumping the switch won’t start the dryer. Test the motor windings for continuity with a multimeter.

To access and test the start switch on a Kenmore 796.81182310:

Unplug dryer

Always unplug the dryer from the electrical outlet before accessing internal components for safety.

Remove console panel

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

The start switch is mounted to the top console panel. Take out the screws to detach the console and access the switch.

Check contacts

Examine the electrical contacts inside the start switch for signs of wear, pitting, or burning. Damaged contacts prevent electrical continuity.

Test with multimeter

Use a multimeter to check for continuity through the start switch when pressed. No continuity indicates a faulty switch in need of replacement.

Inspect wires

Check the switch wiring for any burnt or melted spots that may be interrupting flow. Replace any damaged wires.

Clean contacts

If the contacts are intact, spray them with electrical contact cleaner to remove any debris or buildup preventing contact.

If cleaning or adjusting the start switch doesn’t resolve a no-start problem, replacement is required. Switches are commonly available parts for Kenmore dryers.

While you have the console panel off, also inspect the electrical control board. Look for any burnt components or loose wiring connections that could cause start issues. Reflow any solder joints as needed.

A defective motor centrifuge switch is another possible culprit for dryer no-start conditions. This safety device prevents the motor from operating if the drum is not turning properly. Replace it if faulty.

Insufficient airflow can also cause starting problems on Kenmore dryers. Make sure the blower fan spins freely and the vent ductwork is clear. A clogged lint filter can prevent proper airflow.

It’s worthwhile to fully clean lint buildup from the blower fan, vent system, switches, and control board while troubleshooting start issues. Preventative maintenance can uncover other debris issues before they lead to operating failure.

While a burnt-out motor is less likely, it’s smart to verify the motor windings and centrifugal switch test OK with a multimeter. Swapping in a replacement motor is more labor intensive if that ends up being the root cause.

With some basic electrical testing and component inspection focused first on the start switch, you can often resolve no-start problems on a Kenmore 796.81182310 dryer in an hour or less. Order replacement parts using the spec plate model and serial numbers to get your dryer running again.

Is your Kenmore 81182310 dryer not producing any heat to dry clothes? Before calling a repair technician, check if a blown thermal fuse is the culprit. This inexpensive part fails often and is an easy DIY replacement.

The thermal fuse shuts off power to the heating circuit when the dryer overheats. When it blows, the dryer won’t heat at all. Some common reasons for overheating that blows the fuse include:

Clogged vent

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Restricted airflow causes excess heat buildup. Clean lint from the vent ductwork to allow proper airflow.

Blocked blower

Lint buildup around the blower wheel prevents proper exhaust. Clear lint from the housing and blades.

Faulty thermostats

Defective operating or limit thermostats won’t shut off the heating elements when required. Test thermostats for proper functioning.

Damaged heating element

Shorts or burned sections in the element assembly can overheat and blow the fuse. Inspect the element for damage.

On the Kenmore 81182310, accessing and testing the thermal fuse is straightforward:

Unplug dryer

Always disconnect the power first before working on any dryer components.

Remove back panel

The thermal fuse is located on the blower housing near the heating element duct. Remove the back panel to access it.

Check fuse

Closely inspect the thermal fuse for any signs of melting, burning, or breaks in the fusible link. This indicates it blew open.

Test continuity

Use a multimeter to check for continuity across the fuse contacts. No continuity confirms it’s blown and must be replaced.

Inspect ducts

Check the heating element and blower ducts for lint buildup that may have caused overheating. Clean thoroughly.

Replace fuse

Order and install the same style fuse with the exact temperature rating listed on the dryer data plate. Do not bypass the fuse with wire.

Replacing the thermal fuse should restore heat function if no other components are defective. Some additional troubleshooting tips include:

Test components

Check that heating element, thermostats, motor switch and timer are working properly. Faulty ones can cause thermal fuse failure.

Inspect wiring

Make sure all heater circuit wires are intact with no charring or melting. Replace damaged wires.

Monitor cycling

If the new fuse blows again rapidly, it indicates an underlying overheating issue needs addressed.

Prevent lint buildup

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Regularly cleaning lint traps, filters and ductwork reduces overheating risk and prevents blown fuses.

While the Kenmore 81182310 has the fuse for easy replacement, many models have the fuse mounted on the blower wheel itself. This requires blower removal to access the fuse.

If the fuse keeps blowing after thorough troubleshooting, the problem may lie with the high-limit thermostat or operating thermostat malfunctioning. These will require replacement.

Examine the heating elements as well for shorts, gaps or resistance fluctuations indicating a defective part. An electrician can perform detailed testing if needed.

With some basic multimeter testing and visual inspection focused on the thermal fuse, you can often resolve no-heat issues quickly on a Kenmore dryer. Just be sure to address any overheating issues to prevent failure of the new fuse.

Loud thumping or rattling sounds coming from your Kenmore 796.81182310 dryer? The culprit could be worn out drum support rollers in need of lubrication. With some DIY maintenance, you can often eliminate annoying roller noise and restore quiet operation.

The drum rollers allow the rear drum to turn smoothly as it rotates. Over time, the rollers can wear out or seize up, causing loud rattling or thumping against the dryer cabinet.

To lubricate noisy drum rollers on a Kenmore 796.81182310:

Unplug dryer

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Always unplug the unit before any disassembly or maintenance for safety.

Remove front panel

Take off the top and front panels to access the drum roller assembly in the back corner.

Inspect rollers

Examine each roller for cracks, loosening, or binds preventing free spinning. Badly worn rollers will need replacement.

Clean debris

Use a vacuum and brush to remove built-up lint or debris around the rollers that could cause noise.

Apply lubricant

Put a small amount of dryer-safe lubricant, like lithium grease, on the roller shafts and bearing surfaces.

Test operation

Reassemble the panels and run the dryer empty to check if the lubrication reduced the rattling noise as it operates.

Some other noise troubleshooting tips for Kenmore dryers include:

Inspect mounting

Make sure the roller assembly is seated properly in the brackets. Tighten any loose screws.

Check belt tension

The drive belt slipping can make rattling noises. Check tensioner adjustment and belt condition.

Clear blower housing

Built-up lint around the blower wheel can rattle against the housing. Carefully vacuum out lint.

Tighten cabinet

Loose cabinet screws allow panels and brackets to vibrate. Tighten all interior screws securely.

Adjust leveling

An unleveled dryer can cause vibration and rattling. Adjust the leveling feet to stabilize.

Be sure to clear any lint buildup from the rollers, brackets, cabinet interior and ventilation system. Excess lint accumulation can lead to overheating issues over time.

If lubricating the shaft and bearings doesn’t eliminate the rattling, the rollers may need replacement. Over time, the plastic wheels wear out and develop rough surfaces that cause noise.

Also inspect the felt drum glides near the rollers. Worn out or compressed glides can allow the drum to rub against the metal center post, creating rattling too. Replace any damaged glides.

Check the blower fan as well for any debris stuck in the blades or bent fins that may be rattling against the housing during operation. Carefully straighten or clean the blower.

With some DIY maintenance to lubricate parts and clear built-up lint, you can often resolve annoying rattling noises coming from a Kenmore dryer. But if the rollers show signs of excess wear, replacement may be the longer-term solution.

Is your Kenmore dryer model 796 overheating and shutting off mid-cycle? Before calling for service, check if a clogged exhaust fan is the problem. Cleaning built-up lint from the fan housing and blades can often resolve overheating failures.

The exhaust fan is key for pushing hot, moist air out of the dryer through the vent ductwork. When lint builds up around the fan, it can’t properly circulate airflow, leading to overheating and shutdowns.

Signs your Kenmore may have a blocked exhaust fan include:

Overheating shutdowns

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

If the dryer stops heating mid-cycle, the internal thermostat likely tripped due to excess heat from poor ventilation.

Longer drying times

Restricted airflow from a clogged fan forces the dryer to run longer trying to dry clothes.

Lint escaping into room

A blocked fan can force lint backward into the dryer drum and room instead of outside.

To clean the exhaust fan on a Kenmore model 796:

Unplug dryer

Always unplug the dryer before any disassembly to avoid electric shock risk.

Remove back panel

The exhaust fan housing is located inside the back panel. Remove it to access the fan.

Vacuum housing

Use a vacuum crevice tool to clean lint and debris from the fan housing interior.

Extract fan

Remove the screws to detach the fan assembly for more thorough cleaning.

Clean fan blades

Carefully scrape and vacuum lint off the fan blades, base and motor.

Reassemble

Reinstall the cleaned fan assembly and secure the back panel before using again.

Be sure to clean the full exhaust ducting as well to maximize airflow:

Detach duct

Need Dryer Repair. See If Your Kenmore Model Matches These Common Issues

Separate the flexible ducting from the dryer exhaust vent housing.

Clear duct lint

Run a vacuum hose through the duct to clean out any accumulated lint inside.

Check vent hood

Inspect the outdoor vent hood for damage, clogs, or obstructions impeding airflow.

Routine dryer maintenance should include checking and cleaning the exhaust fan, ducts, and vent hood to prevent overheating issues caused by restricted airflow.

If cleaning the fan and vents doesn’t resolve overheating problems, other potential causes include:

Faulty thermostats

Defective operating or high-limit thermostats can fail to shut off the heating element when required.

Damage heating element

Cracks or shorts in the heating element assembly can lead to uncontrolled overheating.

Blower motor issues

A failing blower motor prevents proper airflow. Inspect the motor if the fan blades are clear of lint.

Be sure to confirm the exhaust duct length is under the recommended 30 feet, and keep duct runs as short and straight as possible. Verify the dryer is properly leveled, as unevenness can impede fan operation.

With a thorough cleaning of the exhaust system and fan, you can often resolve overheating issues on a Kenmore clothes dryer without a costly service call. But take care not to bend fan blades when cleaning, as imbalance can cause noise issues. Replace damaged blades.